This 16-inch Cutter Suction Dredger was built in 2010 and can be purchased with or without a 16″ booster pump. The Dredge and booster barge require trucks for transportation, including one oversize load. It fully meets California environmental regulations and the dredge pump is in excellent condition. Only a few hundred hours on the main engine after a Caterpillar dealer rebuild, and about two thousand hours on the booster pump engine.
Located in the state of California, USA
| Principal Dimensions and Characteristics | ||||
| Year Built: | 2010 | |||
| Length Over All: | 31.09 m | 102 feet | ||
| Width: | 7.19 m | 23.6 feet | ||
| Hull Depth: | 1.52 m | 5 feet | ||
| Ladder Length: | 18.29 m | 60 feet | ||
| Estimated Dry Weight: | 210,000 lbs | |||
| Hull: | ||||
| Center Section (L x W x H): | 10.97 m x 3.54 m x 1.52 m | 36 feet x 11.6 feet x 5 feet | ||
| Side Pontoons (over all) (L x W x H): | 25.30 m x 1.83 m x 1.52 m | 83 feet x 6 feet x 5 feet | ||
| Over All Size: | 25.30 m x 7.19 m x 1.52 m | 83 feet x 23.6 feet x 5 feet | ||
| Hull Skin Thickness: | 6.35 mm (1/4 inch) Steel Skin – | |||
| Heavy Duty Steel Stern & Forward Bulkhead | ||||
| Watertight Bulkheads: | approx. every 3.05 m (10 feet) | |||
| Digging Capacity | ||||
| Min. Digging Depth: | 1.83 m | 6 feet | ||
| Max. Digging Depth @ 60 degree angle: | 13.41 m | 44 feet | ||
| Machinery | ||||
| Main Engine: | ||||
| Make/Model: | Caterpillar/C32 | |||
| Power: | 839 kW | 1,125 hp | ||
| Transmission: | Twin disc Marine Transmission | |||
| Fuel Capacity (shared): | 7,571 liters | 2,000 gallons | ||
| Auxiliary Engine: | ||||
| Make/Model: | Caterpillar/C11 | |||
| Power: | 313 kW | 420 hp | ||
| Transmission: | Funk Hydraulic Drive | |||
| Fuel Capacity (shared): | 7,751 liters | 2,000 gallons | ||
| Pump | ||||
| Make/Model: | Pearce | |||
| Suction Diameter: | 457.2 mm | 18 inches | ||
| Discharge Diameter: | 406.4 mm | 16 inches | ||
| Impeller Diameter: | 1,016 mm | 40 inches | ||
| Cutter | ||||
| Cutter Type: | Cutter head | |||
| ID Size: | 1,092.2 mm | 43 inches | ||
| Edges: | Replaceable Serrated Edges | |||
| Drive: | SAI hydraulic Planetary Drive | |||
| Torque: | 430,000 lbs-in approx. | |||
| Speed: | 0-25 rpm (Variable Speed & Reversible) | |||
| Power: | 149 kW | hp 200 | ||
| Winches | ||||
| Swing Winches (2): | Pullmaster H-18 18,000 lbs Capacity Bare Drum | |||
| Ladder Hoist (1): | Pullmaster M-25 25,000 lbs Capacity Bare Drum | |||
| Spuds (2): | Pullmaster H-18 18,000 lbs Capacity Bare Drum | |||
| All details on these pages are given in good faith and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose is either stated or implied. Prices are subject to change without notice. | ||||