Brand new Mud Cat™ Dredge. This unit has zero hrs on it. It sat on a pond for about 4 months and then has been in a storage container ever since. This unit has several extra’s.
- Radio Remote control with hand held remote
- 600’ of Power Cord
- A/C unit for electrical enclosure
- Hydraulic oil cooling system
- 4 point winch anchoring and tension package
- 600’ 3/8 galvanized traverse cable
- Auto Sense: automated forward / reverse travel control
- 800’ lay flat hose system.
- 5 sets of black saddle floats
Location: State of Arizona
| Principal Dimensions and Characteristics | ||||
| Length Over All: | 30-ft 2-in | 9.2 m | ||
| Width Over All: | 8-ft 7-in | 2.6 m | ||
| Height Over All: | 7-ft 6-in | 2.3 m | ||
| Weight (Dry): | 8,100 lbs | 3650 kg | ||
| Draft: | 15-in | 0.4 m | ||
| Manufacturer: | Mud Cat | |||
| Floatation | ||||
| Pontoons (2) | ||||
| Diameter: | 30-in | 0.8 m | ||
| Length: | 26-ft | 7.9 m | ||
| Steel gauge: | 10 | 3.4 mm | ||
| Cutter Assembly | ||||
| Mud Shield: | Semi-enclosed; anti-turbidity | |||
| Drive System: | Two (2) low speed, high torque motors; dual seals | |||
| Auger Diameter (without cutter knives): | 10-in | 254 mm | ||
| Auger Diameter (with cutter knives): | 15 1/4-in | 387 mm | ||
| Auger Pitch: | 9-in | 228 mm | ||
| Auger Flighting: | 3/8-in | 9.5 | ||
| Speed: | Fixed @ 60 RPM | |||
| Cutter Knives: | Detachable heat-treated blades | |||
| Auger Torque: | 6,000 in-lbs | |||
| Working Capacity | ||||
| Cut: | 7-ft 6-in | 2.3 m | ||
| Operating Depth: | 17-ft | 5.2 m | ||
| Slurry Pump – submersible with cast iron volute and impeller. | ||||
| Power (electric driven): | 100 hp | 76 kW | ||
| Centrifugal Dual Vane Impeller: | 3-in | 76 mm | ||
| Suction Diameter: | 8-in | 200 mm | ||
| Discharge Diameter: | 8-in | 200 mm | ||
| Nominal Pump Performance: | 3,000 GPM (680 m3/hr) against 60 ft (18.3 m) head Up to 260 yds3/hr (200 m3/hr)of production at 30% solids content. |
|||
| Propulsion | ||||
| Double sheave hydraulic-driven winch: | 10-in | 254 mm | ||
| Traverse Speed: | 0-30 FPM | 0-9.4m/min | ||
| Average Cutting Speed: | 8-12 FPM | 2.4-3.7m/min | ||
| Wire Rope Diameter: | 3/8-in | 9.5 mm | ||
| Ladder Hoist | ||||
| Winch Type: | Hydraulic | |||
| Max. Line Pull | 4,000 lbs | 17.8 kN | ||
| Hydraulic Power Unit | ||||
| Power (electrical-driven): | 15 hp | 11.2 kW | ||
| Circuit One: | Auger, Travel and Hoist Winch | |||
| Control System | ||||
| Wireless Radio Remote Control | ||||
| Slurry Pump – On / Speed | Hoist – Up / Off / Down | |||
| Auger – On | Travel – Fwd / Off / Reverse / Speed | |||
| Electrical System | ||||
| Electrical Requirement: | 460 V – 3 Phase – 60 Hz – 165 FLA (standard) | |||
| All details on these pages are given in good faith and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose is either stated or implied. Prices are subject to change without notice | ||||