The hull is composed of three compartments. The hull sides and deck is constructed from 10 gauge plate (3.57 mm). The bottom of the hull is constructed from 3/16” plate (4.7 mm). The ladder is constructed of 3”x3”x3/16” (76 mm x 76 mm x 4.7 mm) angle iron with 7 gauge (4.55 mm) metal plate gussets. The cutterhead has a 27” (686 mm) inside diameter back ring with an outside diameter of 32” (813 mm). The prime mover is a Caterpillar model C13 ACERT diesel engine rated 440 bhp (328 bkW). The dredge pump is a Metso Minerals, Thomas Simplicity series dredge pump model # J30. The nominal flow rate is 3,800 GPM (863 m3/hr) @ 200 feet H2O (61 m H2O). Two (2) spuds are located on the stern of the dredge. The spuds are SCH 40 8-5/8” (219 mm) diameter x 30’ (9.4 m) long.
Built around 2014 and had worked 3411 hours. Recently it has been completely serviced, updated and gone through. It has been painted with polyuria epoxies.
Price includes the following which is located in Mexico
- New pump
- New spare cutting head, the head currently on the dredge is in great shape as well
- Approximately 500 yards of pipeline
- Many floats
- The thermofusion (pipe welding) equipment is in great shape
Location: state of Texas
| General Information | ||||
| Built: | 2014 | |||
| Hours of Operation: | 3411 | |||
| Dimensions and Characteristics | ||||
| Length overall (with ladder): | 20.7 m | 68-ft | ||
| Hull Length: | 15.2 | 50-ft | ||
| Hull Width: | 3.5 m | 11-ft 6-inch | ||
| Hull Depth: | 1.2 m | 4-ft | ||
| Over Height (trucking): | 3.1 m | 10-ft | ||
| Total Dry Weight (approx.): | 26,309 kg | 58,000 lbs | ||
| Diesel Fuel Capacity: | 1,893 liters | 500 gal | ||
| Max Dredging Depth: | 7.6 m | 25-ft | ||
| Engine | ||||
| Make/Model: | Caterpillar model C13 ACERT diesel | |||
| Power: | 328 bkW | 440 bhp | ||
| Dredge Pump | ||||
| Make/Model: | Metso Minerals, Thomas Simplicity series #J30 | |||
| Nominal Flow Rate: | 863 m3/hr | 3,800 gpm | ||
| Cutter | ||||
| Cutter Head (inside diameter): | 686 mm | 27-inch | ||
| Cutter Head (outside diameter): | 813 mm | 32-inch | ||
| Cutter Design: | six (6) smooth blades | |||
| Power at Shaft: | five (5) cylinder Staffa hydraulic motor with model # HMB-200 |
|||
| Ladder and Swing Winches | ||||
| Ladder Length: | 10 m | 33-ft | ||
| Winches Pull Capacity(5): | 20kN | 4,500 lb | ||
| Wire Diameter: | 10 mm | 3/8-inch | ||
| Wire Length: | 45.7 m | 150-ft | ||
| Spuds (2) | ||||
| Length: | 9.4 m | 30-ft | ||
| Diameter: | 219 mm | 8-5/8-inch | ||
| All details on these pages are given in good faith and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose is either stated or implied. Prices are subject to change without notice | ||||